Bucketlist Trading Private Limited

Product Description:

Power relay delay pull. Specifically: 12v power supply to the relay, the relay will not immediately suck and status relay outputs are: normally open disconnected public, normally closed and public conduction; wait until the delay 1-10s (adjustable), the relay suction and, this time, the relay output status is: normally open and public conduction, normally closed and public disconnected; as long as Uninterrupted power module, this state will remain.

The delay time formula: T = 1.1RC

For example : with a 100K resistor and 100uf capacitor; T (Delay Time) = 1.1 x 100000 x 0.0001 = 11 seconds.
The PCB color and relay make may vary based on availability

Applications:

• The delay of the onboard equipment is turned on to prevent the current from being too large to burn the vehicle equipment when the vehicle is on fire.

• It is necessary to have a sequence to start, to prevent multiple devices from simultaneously starting the current and burning the appliance too much.

Specification:

• Module-based on: NE555 chip; The delay time is adjustable (0~10 seconds) using the in-built potentiometer

• Delay module: Delay connect module

• Input voltage: DC12V

• Control voltage : AC 0 - 250V/max. 10A, DC 0 - 30V/max. 10A

• The operating voltage: 12V DC; Max. load : 2200W

Additional Information:

• Item Code: SWD001-NE555-12V
• Delivery Time: 2 - 4 days

Description:

Normally open interface maximum load: AC 250V/10A, DC 30V/10A.

SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA.

Fault-tolerant design, the relay will not move even if the control line is broken.

Power indicator (green), relay status indicator (red).

The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient.

Two module interface:

1. DC+: Connect the power supply positive pole (voltage 5V).

2. DC-: Connect the power negative pole.

3. IN: Low level (3.3V) control relay pull in.

Relay output terminal:

1. NO: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM.

2. COM: Relay common interface

3. NC: Relay normal close, short connected with COM before pulling in and suspended after pulling in.

Specification:

• Operating voltage: DC 5V; Trigger current: 5mA; Normally open interface maximum load: AC 250V/10A, DC 30V/10A.

• Trigger Type: Low = ground level = logic 0 = logical false | High = supply voltage (usually Vcc or Vdd) = logic 1 = logical true.

• This Module Is In Line With International Safety Standard, Control Areas And Load Area Have The Isolation Groove; Blue Kf301 Terminal Line More Convenient.

• Uses The Quality Relay; Dc Or Ac Signal Control, Can Control 220 V Ac Load;

• Have Power And Relay Operation Instructions

Additional Information:

• Item Code: AR0351-1CH-5V-LOW
• Delivery Time: 2 - 4 days

Single channel simple magnetic relay for PCB mount. this module is in line with international safety standard, control areas and load area have the isolation groove; blue KF301 terminal line more convenient. USES the loose quality goods relay; dc or ac signal control, can control 220 v ac load; have power and relay operation instructions, and bright, disconnect the dawn; signal input signal, the public end and will often start conduction; can be used as a microcontroller development board module, can be used as a home appliance control;and one often opened a normally closed contact;

• Protect Feature:Epoxy
• Theory:Voltage Relay
• Size:Miniature
• Model Number:SRD-05VDC-SL-C; Contact Load:Low Power

Additional Information:

• Item Code: AR097-SRD-05VDC-SL-C-DIP-5
• Delivery Time: 2 - 4 days

Description:

• Normally open interface maximum load: AC 250V/10A, DC 30V/10A.

• SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA.

• Fault-tolerant design, the relay will not move even if the control line is broken.

• Power indicator (green), relay status indicator (red).

• The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient.

Specification:

• Operating voltage: DC 5V; Trigger current: 5mA; Normally open interface maximum load: AC 250V/10A, DC 30V/10A.

• Trigger Type: Low = ground level = logic 0 = logical false | High = supply voltage (usually Vcc or Vdd) = logic 1 = logical true.

• This Module Is In Line With International Safety Standard, Control Areas And Load Area Have The Isolation Groove; Blue Kf301 Terminal Line More Convenient.

• Uses The Loose Quality Goods Relay; Dc Or Ac Signal Control, Can Control 220 V Ac Load;

• Have Power And Relay Operation Instructions, And Bright, Disconnect The Dawn;

Two module interface:

1. DC+: Connect the power supply positive pole (voltage 5V).

2. DC-: Connect the power negative pole.

3. IN: Low level (3.3V) control relay pull in.

Relay output terminal:

1. NO: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM.

2. COM: Relay common interface

3. NC: Relay normal close, short connected with COM before pulling in and suspended after pulling in.

 

 

Additional Information:

• Item Code: AR0353-1CH-5V-WO-OPTOCUOUPLER
• Delivery Time: 2 - 4 days

Description:

Normally open interface maximum load: AC 250V/10A, DC 30V/10A.

SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA.

Fault-tolerant design, the relay will not move even if the control line is broken.

Power indicator (green), relay status indicator (red).

The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient.

Two module interface:

1. DC+: Connect the power supply positive pole (voltage 5V).

2. DC-: Connect the power negative pole.

3. IN: Low level (3.3V) control relay pull in.

Relay output terminal:

1. NO: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM.

2. COM: Relay common interface

3. NC: Relay normal close, short connected with COM before pulling inand suspended after pulling in.

• Operating voltage: DC 5V; Trigger current: 5mA; Normally open interface maximum load: AC 250V/10A, DC 30V/10A.
• Trigger Type: Low = ground level = logic 0 = logical false | High = supply voltage (usually Vcc or Vdd) = logic 1 = logical true.
• This Module Is In Line With International Safety Standard, Control Areas And Load Area Have The Isolation Groove; Blue Kf301 Terminal Line More Convenient.
• Uses The Best Quality Relay; DC Or AC Signal Control, Can Control 220 V AC Load;
• Applications: Industrial Fields, PLC control, Household intelligent control;

Additional Information:

• Item Code: AR0352-1CH-5V-RELAY
• Delivery Time: 2 - 4 days

Description:

Normally open interface maximum load: AC 250V/10A, DC 30V/10A.

SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA.

Fault-tolerant design, the relay will not move even if the control line is broken.

Power indicator (green), relay status indicator (red).

The interface is designed humanized, and all the interfaces can be directly connected by wiring terminals, which is very convenient.

Two module interface:

1. DC+: Connect the power supply positive pole (voltage 5V).

2. DC-: Connect the power negative pole.

3. IN: Low level (3.3V) control relay pull in.

Relay output terminal:

1. NO: Relay normal open, the relay suspends before pulling in, and then short-connect with the COM.

2. COM: Relay common interface

3. NC: Relay normal close, short connected with COM before pulling in and suspended after pulling in.

• Operating voltage: DC 5V; Trigger current: 5mA; Normally open interface maximum load: AC 250V/10A, DC 30V/10A.
• Trigger Type: Low = ground level = logic 0 = logical false | High = supply voltage (usually Vcc or Vdd) = logic 1 = logical true.
• This Module Is In Line With International Safety Standard, Control Areas And Load Area Have The Isolation Groove; Blue Kf301 Terminal Line More Convenient.
• Uses The Quality Relay; Dc Or Ac Signal Control, Can Control 220 V Ac Load;
• Have Power And Relay Operation Instructions

Additional Information:

• Item Code: AR0350-1CH-5V-HIGH
• Delivery Time: 2 - 4 days

Product Description:

   Single-channel simple magnetic relay for PCB mount. this module is in line with the international safety standards, control areas and load area have the isolation groove; blue KF301 terminal line more convenient. USES the loose quality goods relay; dc or ac signal control, can control 220 v ac load; have power and relay operation instructions, and bright, disconnect the dawn; signal input signal, the public end and will often start conduction; can be used as a microcontroller development board module, can be used as a home appliance control; and one often opened a normally closed contact;

• Package: Plugin; Manufacturer: Songle Relay

• Relay Type: General Purpose; Coil Type: Non Latching

• Coil Voltage: 6VDC; Contact Form: SPDT

• Contact Rating (Current): 10A

• Switching Voltage: 250VAC (10A), 30VDC (10A)

Additional Information:

• Item Code: AR098-SRD-06VDC-SL-CDIP-5
• Delivery Time: 2 - 4 days

This is a 2 Channel isolated 5V 10A relay module Optocoupler for Arduino PIC ARM. It can be used to control various appliances and other types of equipment with a large current. It can be controlled directly with 3.3V or 5V logic signals from a microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
This relay has a 1×4 (2.54mm pitch) pin header for connecting power (5V and 0V), and for controlling the 2 relays.
The pins are marked on the PCB as:
GND – Connect 0V to this pin.
IN1 – Controls relay 1, active Low Relay will turn on when this input goes below about 2.0V
IN2 – Controls relay 2, active Low Relay will turn on when this input goes below about 2.0V
VCC – Connect 5V to this pin. Is used to power the optocouplers
Note: High level and low level-triggered mode:
High-level trigger refers to the signal voltage between input and trigger, can be understood as a signal input with VCC cathode short-circuit triggered a way; Low-level trigger refers to the signal voltage between the input terminal and Earth OV trigger, can be understood as the signal input terminal and the GND negative electrode short circuit triggered away 1-channel relay module connection Jumper Instruction = The relay can be turned on when we connect 5v to one end and the other to -5v / Gnd, while talking about the jumper, if we short the VCC and the middle pin, then our relay will act as high level-triggered relay means that when we will apply + 5V input on its input pin it will be turned on and when the jumper will be set to “middle and GND”, it will act as a low-level triggered relay, It means that relay will be triggered when we implement the 5V / GND on its input pin.

• Operating voltage: DC 5V; Trigger current: 5mA; Normally open interface maximum load: AC 250V/10A, DC 30V/10A.
• Trigger Type: Low = ground level = logic 0 = logical false | High = supply voltage (usually Vcc or Vdd) = logic 1 = logical true.
• This Module Is In Line With International Safety Standard, Control Areas And Load Area Have The Isolation Groove; Blue Kf301 Terminal Line More Convenient.
• Uses The Best Quality Relay; DC Or AC Signal Control, Can Control 220 V AC Load; Around the board with 4 mounting holes, hole diameter 3. 1 mm, easy installation and fixing
• 2 LEDs to indicate when relays are ON. Works with logic level signals from 3.3V or 5V devices

Additional Information:

• Item Code: AR036-2CH-5V-RELAY
• Delivery Time: 2 - 4 days

• Package: Plugin; Manufacturer: Songle Relay
• Coil Voltage: 9VDC; Contact Form: SPDT; Contact Rating (Current): 10A Switching Voltage: 250VAC (10A), 30VDC (10A)
• Relay Type: General Purpose; Coil Type: Non Latching
• Model Number: SRD-09VDC-SL-C; Contact Load:Low Power
• Coil Voltage/Nominal Voltage: 9VDC; Nominal Current: 50mA; Coil Resistance: 180ohms +/- 10%

Additional Information:

• Item Code: AR0103-SRD-09VDC-SL-CDIP-5
• Delivery Time: 2 - 4 days

Single channel simple magnetic relay for PCB mount. this module is in line with international safety standard, control areas and load area have the isolation groove; blue KF301 terminal line more convenient. USES the loose quality goods relay; dc or ac signal control, can control 220 v ac load; have power and relay operation instructions, and bright, disconnect the dawn; signal input signal, the public end and will often start conduction; can be used as a microcontroller development board module, can be used as a home appliance control;and one often opened a normally closed contact;

• Package: Plugin; Manufacturer: Songle Relay
• Relay Type: General Purpose; Coil Type: Non Latching
• Coil Voltage: 12VDC; Contact Form: SPDT
• Contact Rating (Current): 10A
• Switching Voltage: (250VAC , 30VDC) Max               

Additional Information:

• Item Code: AR099-SRD-12VDC-SL-CDIP-5
• Delivery Time: 2 - 4 days

Size name:3VDC 5PIN

Single channel simple magnetic relay for PCB mount. this module is in line with international safety standard, control areas and load area have the isolation groove; blue KF301 terminal line more convenient. USES the loose quality goods relay; dc or ac signal control, can control 220 v ac load; have power and relay operation instructions, and bright, disconnect the dawn; signal input signal, the public end and will often start conduction; can be used as a microcontroller development board module, can be used as a home appliance control;and one often opened a normally closed contact;

• Protect Feature:Epoxy
• Theory:Voltage Relay
• Size:Miniature
• Model Number:SRD-05VDC-SL-C; Contact Load:Low Power

Additional Information:

• Item Code: AR0102-SRD-03VDC-SL-CDIP-5
• Delivery Time: 2 - 4 days